Raspberry Pi 4 Overclocking

🎯 Overview

This tutorial will guide you through safely overclocking your Raspberry Pi 4 for maximum performance. We'll start conservative and work up to more aggressive settings.

⚠️ Important Warnings

Before you start:

• Overclocking voids warranty and can damage your Pi if done incorrectly
• Always have a backup SD card - bad settings can prevent booting
• Proper cooling is essential - consider a fan or heatsink
• Monitor temperatures constantly during testing
• Start conservative and work your way up

🔧 Prerequisites

Required Hardware

• Raspberry Pi 4 (any RAM variant)
• Quality power supply (official 3A+ recommended)
• Cooling solution (fan, heatsink, or both)
• Backup SD card for recovery

Proven High-Performance Setup

The aggressive overclocking configuration in this tutorial was tested with this specific hardware combination that achieved excellent 44-48°C temperatures:

Hardware Used/Recommended (Alternatives Can Be Used):

• Case: Mini desktop case for Raspberry Pi (https://a.co/d/6c1EEqu)
• Storage: SATA M.2 SSD (instead of SD card for better performance/reliability)
• Cooling: Ice Tower fan cooler with thermal pads
• Power: Official Raspberry Pi power supply
• Case fans: None (just the CPU cooler fan)

This setup demonstrates that excellent cooling performance is achievable with the right CPU cooler, even without additional case ventilation.

Software Requirements

# Install monitoring and stress testing tools
sudo apt update
sudo apt install stress htop

📁 Understanding the Config File

The overclocking settings are stored in the boot configuration file:

Location (newer Pi OS):

sudo nano /boot/firmware/config.txt

Location (older Pi OS):

sudo nano /boot/config.txt

Note: If you're using an M.2 SSD like in our proven setup, you'll still edit the same config file - the Pi boots from the SSD but uses the same configuration structure.

Storage Performance Benefits

Using an M.2 SSD (as in our test setup) provides additional benefits when overclocking:

• Faster I/O operations reduce system bottlenecks
• Lower power consumption vs SD cards
• Better thermal characteristics (SSDs generate less heat than SD cards under load)
• Improved reliability for sustained high-performance operation

Key Settings Explained

arm_freq=1500          # CPU frequency in MHz (stock is 1500)
over_voltage=0         # Additional voltage (0-8, higher = more power)
gpu_freq=500           # GPU frequency in MHz (stock is 500)
core_freq=500          # Core frequency in MHz
sdram_freq=3200        # RAM frequency in MHz
temp_limit=85          # Thermal throttling temperature (°C)
arm_boost=1            # Enable dynamic frequency scaling

🟢 Step 1: Conservative Overclock (Safest Start)

Add these settings to your config.txt:

# Conservative overclock - safe for most setups
arm_freq=1750          # +250MHz from stock
over_voltage=2         # Minimal voltage increase
gpu_freq=600           # +100MHz GPU
core_freq=550          # +50MHz core
temp_limit=80          # Conservative temperature limit

Test this setup:

1. Save the file and reboot: sudo reboot
2. Check temperatures: vcgencmd measure_temp
3. Verify frequencies: vcgencmd measure_clock arm
4. Run stress test: stress --cpu 4 --timeout 300

Expected results:

• Temperatures under 65°C during stress testing
• No throttling: vcgencmd get_throttled should return 0x0

🟡 Step 2: Moderate Overclock (Good Balance)

If Step 1 was stable, try these settings:

# Moderate overclock - requires decent cooling
arm_freq=1900          # +400MHz from stock
over_voltage=4         # Moderate voltage increase
gpu_freq=700           # +200MHz GPU
core_freq=575          # +75MHz core
sdram_freq=3400        # RAM overclock
temp_limit=78          # Slightly lower temp limit

Test thoroughly:

• Stress test for 15+ minutes
• Monitor for thermal throttling
• Test real-world applications

🟠 Step 3: Aggressive Overclock (Maximum Performance)

⚠️ Only attempt with excellent cooling!

# Aggressive overclock - requires fan/excellent cooling
arm_boost=1            # Enable dynamic scaling
arm_freq=2100          # +600MHz from stock
over_voltage=6         # High voltage (max safe level)
gpu_freq=750           # +250MHz GPU
core_freq=600          # +100MHz core
sdram_freq=3600        # High RAM speed
temp_limit=75          # Lower temp limit for safety

🌡️ Temperature Monitoring

Essential Commands

# Current temperature
vcgencmd measure_temp

# Continuous monitoring
watch -n 1 vcgencmd measure_temp

# Check for throttling
vcgencmd get_throttled

# Current frequencies
vcgencmd measure_clock arm
vcgencmd measure_clock gpu
vcgencmd measure_clock core

Temperature Guidelines

• Idle: 35-50°C (depending on ambient temperature)
• Light load: 45-60°C
• Heavy load: 60-75°C (with good cooling)
• Throttling starts: 80°C (default, adjustable with temp_limit)

🧪 Stress Testing Protocol

CPU Stress Test

# 10-minute CPU stress test
stress --cpu 4 --timeout 600

# Monitor during test (in separate terminal)
watch -n 1 'vcgencmd measure_temp && vcgencmd get_throttled'

GPU Stress Test

# Install GPU stress test
sudo apt install mesa-utils

# Run GPU benchmark
glxgears -fullscreen

Stability Indicators

✅ Stable system:

• Temperatures stay under temp_limit
• get_throttled returns 0x0
• No random crashes or freezes
• Consistent performance

❌ Unstable system:

• Frequent crashes or freezes
• Random corruption or errors
• Throttling occurring regularly
• System becoming unresponsive

🎛️ Advanced Settings

Fan Control (Recommended)

# Add to config.txt for automatic fan control
dtoverlay=gpio-fan,gpiopin=14,temp=60000

Ice Tower Cooler Setup: The proven configuration uses an Ice Tower fan cooler with thermal pads, controlled via GPIO pin 14. The 60°C activation temperature (60000 in the overlay) provides excellent thermal management:

• Below 60°C: Passive cooling via the large heatsink
• Above 60°C: Active cooling engages automatically
• Result: Even with 2100MHz overclock, temperatures stay in the 44-48°C range

This demonstrates that a quality CPU cooler can eliminate the need for additional case fans.

Memory Optimization

# Adjust GPU memory split (if not using desktop)
gpu_mem=64            # Minimum for headless setups
# OR
gpu_mem=128           # Good for desktop use

Power Management

# Ensure consistent performance
core_freq_min=500     # Prevent core from scaling too low

📋 Complete Working Configuration

Here's a proven aggressive configuration that achieved 44-48°C temperatures with the hardware setup described above (Ice Tower cooler, M.2 SSD, mini desktop case, official Pi power supply):

Hardware Context:

• Mini desktop case with no additional case fans
• Ice Tower fan cooler with thermal pads
• SATA M.2 SSD storage
• Official Raspberry Pi power supply

Results: Stable 2100MHz operation with excellent thermal performance

# Automatically load overlays for detected cameras
camera_auto_detect=1
# Automatically load overlays for detected DSI displays
display_auto_detect=1
# Automatically load initramfs files, if found
auto_initramfs=1
# Enable DRM VC4 V3D driver
dtoverlay=vc4-kms-v3d
max_framebuffers=2
# Don't have the firmware create an initial video= setting in cmdline.txt.
disable_fw_kms_setup=1
# Run in 64-bit mode
arm_64bit=1
# Disable compensation for displays with overscan
disable_overscan=1

# OVERCLOCKING SETTINGS
arm_boost=1            # Enable dynamic frequency scaling
arm_freq=2100          # Aggressive CPU overclock
over_voltage=6         # Maximum safe voltage
gpu_freq=750           # High GPU frequency
sdram_freq=3600        # High RAM speed
temp_limit=75          # Conservative temperature limit

[cm4]
otg_mode=1

[cm5]
dtoverlay=dwc2,dr_mode=host

[all]
core_freq=600
core_freq_min=500
dtoverlay=gpio-poweroff,gpio_pin=26,active_low=0
dtoverlay=gpio-ir,gpio_pin=13
dtoverlay=gpio-fan,gpiopin=14,temp=60000

Note: The gpio-fan overlay is configured for the Ice Tower cooler to activate at 60°C, providing excellent thermal management for this aggressive overclock.

🆘 Troubleshooting:

Pi Won't Boot

1. Remove SD card and edit config.txt on another computer
2. Comment out overclocking lines (add # at the beginning)
3. Boot with safe settings and retry

System Unstable

1. Reduce frequencies by 50-100MHz increments
2. Lower voltage by 1-2 steps
3. Increase temp_limit if thermal throttling occurs
4. Improve cooling if temperatures too high

Performance Not Improving

1. Verify frequencies are actually changing: vcgencmd measure_clock arm
2. Check for throttling: vcgencmd get_throttled
3. Ensure adequate power supply (3A+ recommended)

📊 Performance Expectations:

Typical Improvements

• CPU performance: 20-40% improvement with aggressive overclock
• GPU performance: 30-50% improvement in graphics tasks
• Memory bandwidth: 10-20% improvement with RAM overclock

Benchmarking

# CPU benchmark
sysbench cpu --threads=4 run

# Memory benchmark  
sysbench memory run

# Before/after comparison recommended

🎯 Final Tips

1. Start small - work your way up gradually
2. Test thoroughly - run stress tests for extended periods
3. Monitor always - keep an eye on temperatures
4. Backup everything - save working configurations
5. Document settings - note what works for your specific setup
6. Consider your use case - aggressive overclocks may not be worth it for simple tasks

⚖️ Risk vs. Reward

Conservative overclocking:

• ✅ Low risk, moderate performance gain
• ✅ Good for 24/7 operation
• ✅ Minimal cooling requirements

Aggressive overclocking:

• ⚠️ Higher risk, maximum performance
• ⚠️ Requires excellent cooling
• ⚠️ May reduce hardware lifespan
• ⚠️ Best for short-duration intensive tasks

Remember: The goal is finding the sweet spot between performance and stability for YOUR specific use case and cooling setup!

Created & Maintained by Pacific Northwest Computers

Pacific NW Computers

www.linktr.ee/pnwcomputers

www.pacificnwcomputers.com

📞 Pacific Northwest Computers offers remote and onsite support across: 
Vancouver WA, Battle Ground WA, Camas WA, Washougal WA, Longview WA, Kelso WA, and Portland OR